Book

What're your thoughts on A Step-by-Step Guide to Installing a Bathtub?

Installing a tub isn't precisely brain surgery, yet it does require strong plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old bath tub with a new one is also a moderately challenging project. If the old bathtub is conveniently available, the job can relocate quickly; if you have to open up a wall surface to remove the old bathtub and also place the brand-new bathtub, the task is a lot harder. In either case, the project is within a residence handyman's skills, although you will certainly require an assistant to vacate the old bathtub and also embeded in the new one. Make certain you have qualified on your own for the work and also fit attempting it. As opposed to working with a contractor to take control of a halfway-completed job, it is much better to consider employing one prior to you begin. Possibilities are you may require a professional plumber to make tube links.
This post will assist you install a brand-new bathtub in your shower room if you have currently purchased a new bathtub as well as don't require to alter the arrangement of your previous water system pipes.
Your tools and also product checklist ought to comprise the following:

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Removing Old Taps

If you require to change old taps with new ones as a part of your installment, after that the first thing you ought to do is separate the water. After doing so, switch on the taps to drain any water staying in the system. The procedure of removing the existing taps can be rather bothersome as a result of the restricted gain access to that is often the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a towel all set for the staying water that will come from the pipelines. As soon as the supply pipes have been eliminated, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning during this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old securing compound.
Prior to carrying on to fit the new faucets, contrast the pipe connections on the old taps to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.

Fitting New Taps

If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end offers a link to the current supply pipes.
If you require to fit a monobloc, after that you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin ensuring that the washing machines are in place between the tap and also the sink. Secure the tap in position with the supplier given backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type must be connected to the tap finishes first, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

Installing the Bathtub

Using the two wood boards under its feet, position the bath tub in the called for placement. The wooden boards are handy in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The next objective is to ensure that the bath tub is leveled all round. This can be attained by inspecting the level as well as changing the feet on the bathtub till the spirit level reviews level.
To install faucets, fit the bottom of the outermost versatile tap connector to the proper supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Activate the supply of water as well as examine all joints and also new pipework for leaks as well as tighten them if necessary. Load the tub as well as likewise examine the overflow electrical outlet and also the regular electrical outlet for leaks.
Ultimately, take care of the bathroom paneling as explained in the maker's user's manual. Tiling as well as securing around the tub must wait until the tub has been made use of at the very least once as this will certainly settle it into its final setting.

Getting ready for the Installment

To start with, the sustaining structure provided with the bath needs to be fitted (if required) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is important to see to it that if the tap includes a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps system to avoid stress on the bathtub.
Fit the flexible tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you utilize every one of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to now prepare to be fitted in its last placement.

Tiling Around the Tub

In the location where the bath meets the tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to split a stiff seal, causing the water to penetrate the wall surface in between the bath as well as the tiling, resulting in complications with moisture and feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures as well as fittings. They are sold in tubes and cartridges, and also are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill up the bath tub with water prior to sealing, to allow for the activity experienced when the tub remains in usage. The sealer can split fairly very early if you do not consider this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally easily readily available on the market. It is advisable to fit the floor tiles using waterproof or waterproof glue and also cement.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

I recently found that entry about How to Install a Bathtub Yourself while doing a lookup on the search engines. Do you know another individual who is curious about Tools You Need to Install a New Bathtub ? Feel free to promote it. Thank you for your time. Visit again soon.

For true quality, dial!